|
Date
|
Inspection Type
|
Score
|
Expand All
|
|
08/15/2023
|
 ROUTINE INSPECTION
|
99%
|
|
-
-
Observed torn gasket on reach-in-freezer door.
(4-501.11) (A) EQUIPMENT shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 and 4-2.
(B) EQUIPMENT components such as doors, seals, hinges, fasteners, and kick plates shall be kept intact, tight, and adjusted in accordance with manufacturer's specifications.
(C) Cutting or piercing parts of can openers shall be kept sharp to minimize the creation of metal fragments that can contaminate FOOD when the container is opened.
|
|
08/31/2022
|
ROUTINE INSPECTION
|
98%
|
|
-
-
Observed ice buckets at ice machine not stored inverted. Exposed to splash and dust.
(4-903.11)(A) Except as specified in ¶ (D) of this section, cleaned EQUIPMENT and UTENSILS, laundered LINENS, and SINGLE-SERVICE and SINGLE-USE ARTICLES shall be stored:
(1) In a clean, dry location;
(2) Where they are not exposed to splash, dust, or other contamination; and
(3) At least 15 cm (6 inches) above the floor.
(B) Clean EQUIPMENT and UTENSILS shall be stored as specified under ¶ (A) of this section and shall be stored:
(1) In a self-draining position that allows air drying; and
(2) Covered or inverted.
(C) SINGLE-SERVICE and SINGLE-USE ARTICLES shall be stored as specified under ¶ (A) of this section and shall be kept in the original protective PACKAGE or stored by using other means that afford protection from contamination until used.
(D) Items that are kept in closed PACKAGES may be stored less than 15 cm (6 inches) above the floor on dollies, pallets, racks, and skids that are designed as specified under § 4-204.122.
-
-
Observed fan coverings in the walk-in-cooler unclean.
(4-602.13)NonFOOD-CONTACT SURFACES of EQUIPMENT shall be cleaned at a frequency necessary to preclude accumulation of soil residues.
Observed torn gasket on the reach-in-freezer.
(4-501.11) (A) EQUIPMENT shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 and 4-2.
(B) EQUIPMENT components such as doors, seals, hinges, fasteners, and kick plates shall be kept intact, tight, and adjusted in accordance with manufacturer's specifications.
(C) Cutting or piercing parts of can openers shall be kept sharp to minimize the creation of metal fragments that can contaminate FOOD when the container is opened.
|
|
08/06/2021
|
FOLLOW UP INSPECTION
|
99%
|
|
-
-
See previous routine inspection report.
|
|
08/05/2021
|
ROUTINE INSPECTION
|
97%
|
|
-
-
Observed visible light under the front door.
(6-202.15) (A) Except as specified in ¶¶ (B), (C), and (E) and under ¶ (D) of this section, outer openings of a FOOD ESTABLISHMENT shall be protected against the entry of insects and rodents by: (1) Filling or closing holes and other gaps along floors, walls, and ceilings;
(2) Closed, tight-fitting windows; and
(3) Solid, self-closing, tight-fitting doors. (B) Paragraph (A) of this section does not apply if a FOOD ESTABLISHMENT opens into a larger structure, such as a mall, airport, or office building, or into an attached structure, such as a porch, and the outer openings from the larger or attached structure are protected against the entry of insects and rodents.
(C) Exterior doors used as exits need not be self-closing if they are:
(1) Solid and tight-fitting;
(2) Designated for use only when an emergency exists, by the fire protection authority that has jurisdiction over the FOOD ESTABLISHMENT; and
(3) Limited-use so they are not used for entrance or exit from the building for purposes other than the designated emergency exit use.
(D) Except as specified in ¶¶ (B) and (E) of this section, if the windows or doors of a FOOD ESTABLISHMENT, or of a larger structure within which a FOOD ESTABLISHMENT is located, are kept open for ventilation or other purposes or a TEMPORARY FOOD ESTABLISHMENT is not provided with windows and doors as specified under ¶ (A) of this section, the openings shall be protected against the entry of insects and rodents by:
(1) 16 mesh to 25.4 mm (16 mesh to 1 inch) screens;
(2) Properly designed and installed air curtains to control flying insects; or
(3) Other effective means.
(E) Paragraph (D) of this section does not apply if flying insects and other pests are absent due to the location of the ESTABLISHMENT, the weather, or other limiting condition.
-
-
Observed rust on shelving in walk-in-cooler. *REPEAT VIOLATION
Observed dust build up on fan coverings in walk-in-cooler. *REPEAT VIOLATION
(4-602.13)NonFOOD-CONTACT SURFACES of EQUIPMENT shall be cleaned at a frequency necessary to preclude accumulation of soil residues.
|
